There is a 10-14 day lead time on all Rust-Oleum products due to COVID-19, we apologise for the inconvenience

Rust-Oleum Noxyde is the ultimate water based corrosion protection

Single pack, water-based elastomeric coating based on a modified acrylic binder with unequalled corrosion protection, >15 years in the highest corrosion class C5-M, according to ISO 12944.

Recommended use
1. On iron, steel, special alloys, galvanised and metallised iron and steel, aluminium, copper, zinc, lead, etc. as rust prevention or waterproofing. For outside and inside use.
2. Diluted with 25% water as an adhesion primer coat on slightly or non porous substrates such as glass, smooth bricks and concrete, ceramics, tiles, etc.

  • Ultimate corrosion protection, even in severe conditions
  • 200% elastic coat does not crack or peel
  • Excellent coverage of nuts, bolts and welds
  • Dry fall: saves preparation & clean up time
  • Primer and topcoat in one
  • UV- and impact-resistant
  • Available in a satin finish and 16 colours

 

Specifications

  Surfaces   aluminium, bare or blasted metal, galvanised steel, non-ferro metal, prepainted metal, rusted metal, stainless steel
  Interior/Exterior   exterior
  Drying time   at 20°C touch dry in 1.5 hours, overcoat after 24 hours, fully cured in two weeks
  Coverage   depends on porosity & roughness of the substrate but as a guide:-
  Brush/roller: 200 - 300 g/m²/coat. Airless: 300 - 500 g/m²/coat.
  Total consumption for optimal rust preventive protection: 800 g/m² (in 2 coats) = 350 µm dry film thickness
  Shelf life   four years in sealed containers, if stored in dry, well ventilated areas
  Min. app. temp.   8°C

 

Surface Preparation

Remove grease, oil and all other surface contaminations by alkaline or high pressure (steam) cleaning (max. 200 Bars) in combination with appropriate detergents. The substrate has to be dust free and made rust free by means of sandblasting (Sa2, St2) or high pressurewater jetting (min. 600 Bars). After jetting, the substrate has to be dust free. On newgalvanised surfaces, newzinc, aluminium, stainless steel, apply first a coat of Pegalink. On ferrous substrates, apply Noxyde in red or grey as the first coat. In all instances apply contrasting Noxyde colours for subsequent layers.

Mixing

Mix thoroughly prior to use.

Application

Temperature between 8 and 55°C / Air humidity max. 80% R.H. The substrate temperature must be at least 5°C above dewpoint.

Application & thinning: brush
Undiluted as a rust preventive paint. Diluted with approximately 25% volumewater as an adhesion primer (consumption about 100 g/m²).

Application & thinning: roller
Undiluted as a rust preventive paint. Diluted with approximately 25% volumewater as an adhesion primer (consumption about 100 g/m²)

Application & thinning: Airless spray
Undiluted. Nozzle: 13 - 17 / Pressure: min. 170 bars. Nozzle and pressure can vary depending on the type of substrate, equipment and the experience of the applicator.

Application & thinning: Air-atomised spray
Spray undiluted, Nozzle: 13-17 / Pressure: mín. 170 bar.

Technical Datasheet (PDF)
Safety Data Sheet SDS (PDF)
Noxyde Brochure

Write a review

Note: HTML is not translated!
    Bad           Good

Rust-Oleum Mathys Noxyde

  • Brand: Rust-Oleum
  • Product Code: RO-MN
  • Availability: In Stock
  • £53.99

  • Ex Tax: £44.99


Available Options