Our industrial concrete floor leveller has 33% greater compressive strength than most concrete surfaces and 90% greater tensile strength. it is a pourable self levelling resurfacer for damaged or rough concrete surfaces. Floor Leveller contains reinforcing polyamide fibres for superior strength, shock and abrasion resistance, it is suitable for forklift traffic and general industrial use

FREE DELIVERY TO UK MAINLAND

FixMaster Concrete Floor Leveller is an industrial quality, rough surface smoothing compound for concrete. Easy to use leaving a strong, non-dusting finish. Floor Leveller can be left as a wearing surface or sealed and coated with FixMaster Epoxy Paint WB to give a protective and decorative finish.   

  • Easy to use: pre-measured components
  • Designed for warehouse and industrial floors when rapid strength and durability are a high priority
  • Two primers included, nearly all types of rough surface can be covered
  • Fibre reinforced fot a stronger, more durable surface
  • Self smoothing
  • Application depth from as little as 3mm up to 15mm
  • Suitable for interior or exterior use
  • Can be overpainted if a sealed or anti-slip surface is required

 

Specifications

  Surfaces   worn, rough or damaged concrete floors
  Interior/Exterior   interior
  Curing time   light traffic after 6-8 hours, full cure after 24 hours at 5mm. Thicker applications will take longer
  Primer required?   yes, included in pack
  Coverage   3.75m² @ 3mm thick, 2.2m² @ 5mm and 1.1m² @ 10mm per 25kg
  Shelf life   one year in sealed containers
  NB   Floor Leveller should not be applied at less than 3mm or more than 15mm

 

Surface Preparation

Concrete should be clean and free from loose material. If the surface has previously been  painted the majority should be removed, especially if there are signs of loose or flaking edges. Small amounts of well bonded paint may remain, however if in doubt please call us. Do not apply to surfaces where sugar or sugar solution has been stored or allowed to contaminate the surface
 

Surface Priming

Two primers are supplied, primer 1 and primer 2. 
Primer 1 is to be used on porous surfaces. The concrete should be dampened with clean water, left for 30 minutes before evenly applying primer 1 with a brush or broom. Once dry primer 2 can be applied and the Floor Leveller mixed and laid straight onto primer 2 whilst still wet. Ensure to apply the primers evenly to avoid ponding as any excess primer can be drawn to the surface to leave a milky residue. This does  not  affect  the products strength but can create an uneven appearance and causes problems with over coating. 
 

Mixing

Whilst mixing, pour the resin into the tub and slowly add the powder. Mix using a drill fitted with a mixing blade until a uniform, lump free consistency is obtained, this will take approximately 3-4 minutes.
 

Application

Do not apply below 5°C or above 25°C. Pour the mixed slurry straight onto the wet primer 2 and spread evenly at the desired thickness using a steel float. Any marks from spreading will level out. A spiked roller to release air should be passed through the Floor Leveller 3 or 4 times at different directions within 15 minutes of pouring to ensure roller marks do not remain visible when dried. Where possible, try to avoid applications being left to cure in direct sunlight as this can cause hairline cracking.  

 

Concrete Floor Leveller TDS (PDF)                 Concrete Floor Leveller SDS (PDF)

Write a review

Note: HTML is not translated!
    Bad           Good

Concrete Floor Leveller 25kg

  • Brand: FixMaster
  • Product Code: FM/Floorleveller
  • Availability: In Stock
  • £54.00

  • Ex Tax: £45.00


Related Products

Epoxy Paint Gloss WB 5L

Epoxy Paint Gloss WB 5L

Epoxy Paint Gloss WB is a high grade epoxy resin coating with a gloss chemical resistant finish..

£86.40 Ex Tax: £72.00

Tags: concrete resurfacer, floor leveller, concrete floor leveller, uneven concrete, floor resurfacer